Ultima Oil Pump Manual

1. Ultima Oil Pump Manual Briggs And Stratton
2. Ultima Oil Pump
3. Ultima Oil Pump Diagram

• THINKWORK Oil Change Pump Extractor, 12v 80w Marine Oil Change Pump and Electric Oil Pump, Great Choice for Oil Changes in Car, Ship, Truck, Motorcycle 4.1 out.
• Ultimate oil-free efficiency - guaranteed. Ultima contributes to bottom line cost savings in many ways. Not only do they deliver outstanding efficiency and significantly lower lifecycle costs, the Ultima requires on average, 3.4 m³ less space (or up to 37% less floor space) than a conventional two-stage oil-free compressor.

Removal and Installation

Ultima® Billet Oil Pumps. STANDARD VOLUME OIL PUMP?1 98-610 pump base, 92' & later 98-608 pump base, 84'-91. The oil pump used in the Nissan Altima is a sump pump that secures to the oil pickup tube inside the oil pan. To get to the oil pump so you can replace it, you must remove the oil pan from the engine. This makes the job somewhat labor intensive and time-consuming. However, if you continue to drive your Altima. The oil's viscosity should be matched with the climate conditions but in most cases Ultima 20w50 motor oil will work fine. Page 12: General Information General Information Compression Release Valves 100-107-113-120-127-130-140 CI ® All Ultima 100 CI and larger engines are supplied with manually operated push button compression release valves.

REMOVAL

1. Remove the timing chain. Refer to EM-163, 'Removal'.

2. Remove oil pump assembly.

INSTALLATION

Installation is in the reverse order of removal.

Disassembly and Assembly

1. Oil pump housing

2. Outer rotor

3. Inner rotor

4. Oil pump cover

5. O-ring

6. Regulator valve set

7. Regulator valve

8. Spring

9. Regulator plug

10. Oil strainer

CAUTION: Before assembly apply new engine oil to the parts as shown above.

DISASSEMBLY

1. Remove the oil pump cover.

2. Remove inner rotor and outer rotor from oil pump housing.

3. Remove oil strainer from oil pump housing.

4. After removing regulator plug, remove spring and regulator valve.

INSPECTION AFTER DISASSEMBLY

Clearance of Oil Pump Parts

The JCM Model G585 is a highly sophisticated and high - end electronic cash register (ECR), designed for the hardware, apparel, luncheonette,supermarket, grocery, fast food,and bar/restaurant markets. Additional the function of Model G585 ECR is very agility, so User can program them in order to satisfy your practical transaction needs. Jcm gold cash register user manual. Thank you for purchasing this Electronic Cash Register. Please read this manual carefully before operating your register and keep it at hand for future reference. We hope it will be helpful to you if you encounter any operational problem. Page 41 ELECTRONIC CASH REGISTER JCM GOLD G-105 Owner Manual. Page 42 G105 JCMHK 9910. JCM GOLD Cash Register User Manuals Download ManualsLib has more than 1 JCM GOLD Cash Register manuals Click on an alphabet below to see the full list of models starting with that letter: # 0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z.

• Measure clearance with feeler gauge.

Ultima Oil Pump Manual Briggs And Stratton

• Clearance between outer rotor and oil pump body (position 1).

Standard : 0.114 - 0.260 mm (0.0045 - 0.0102 in)

• Tip clearance between inner rotor and outer rotor (position 2).

Standard : Below 0.180 mm (0.0071 in)

• Measure clearance with feeler gauge and straightedge.

• Side clearance between inner rotor and oil pump body (position 3).

Standard : 0.030 - 0.070 mm (0.0012 - 0.0028 in)

• Side clearance between outer rotor and oil pump body (position 4).

Standard : 0.050 - 0.110 mm (0.0020 - 0.0043 in)

• Calculate the clearance between inner rotor and oil pump body as follows.

1. Measure the outer diameter of protruded portion of inner rotor (position A).

2. Measure the inner diameter of oil pump body with inside micrometer (position B).

(clearance 5) = (inner diameter of oil pump body B) – (outer diameter of inner rotor A)

Standard : 0.045 - 0.091 mm (0.0018 - 0.0036 in)

Regulator Valve

1. Visually inspect components for wear and damage.

2. Check oil pressure regulator valve sliding surface and valve spring.

3. Coat regulator valve with engine oil. Check that it falls smoothly into the valve hole by its own weight.

If damaged, replace regulator valve set or oil pump body.

Regulator Valve Clearance

(Clearance 6) = D (Valve hole diameter) – E (Outer diameter of valve)

Standard : 0.040 - 0.097 mm (0.0016 - 0.0038 in)

If it exceeds the standard, replace the oil pump body.

CAUTION: Coat regulator valve with engine oil.

Check that it falls smoothly into the valve hole by its own weight.

Assembly

Assembly is in the reverse order of disassembly.

Ultima Oil Pump

• Assemble the inner rotor and outer rotor with the punched marks on the oil pump cover side.

CAUTION: Before assembly apply new engine oil to the parts as specified.

Checking bulbs
With all doors closed, apply the parking brake and place the ignition switch to the ON position without starting the engine. The following lights will come on: The following lights (if equipped) come on briefly and then go off: If any light fails to come on, it may indicate a burned-out b ..

Door speaker (coupe)
Description The audio unit sends audio signals to the BOSE speaker amp. The BOSE speaker amp. amplifies the audio signals before sending them to the door speakers using the audio signal circuits. Diagnosis Procedure 1.HARNESS CHECK 1. Disconnect BOSE speaker amp. connector B121 and suspec ..

2. Check oil pressure regulator valve sliding surface and valve spring.

3. Coat regulator valve with engine oil. Check that it falls smoothly into the valve hole by its own weight.

If damaged, replace regulator valve set or oil pump body.

Regulator Valve Clearance

(Clearance 6) = D (Valve hole diameter) – E (Outer diameter of valve)

Standard : 0.040 - 0.097 mm (0.0016 - 0.0038 in)

If it exceeds the standard, replace the oil pump body.

CAUTION: Coat regulator valve with engine oil.

Check that it falls smoothly into the valve hole by its own weight.

Assembly

Assembly is in the reverse order of disassembly.

Ultima Oil Pump

• Assemble the inner rotor and outer rotor with the punched marks on the oil pump cover side.

CAUTION: Before assembly apply new engine oil to the parts as specified.

Checking bulbs
With all doors closed, apply the parking brake and place the ignition switch to the ON position without starting the engine. The following lights will come on: The following lights (if equipped) come on briefly and then go off: If any light fails to come on, it may indicate a burned-out b ..

Door speaker (coupe)
Description The audio unit sends audio signals to the BOSE speaker amp. The BOSE speaker amp. amplifies the audio signals before sending them to the door speakers using the audio signal circuits. Diagnosis Procedure 1.HARNESS CHECK 1. Disconnect BOSE speaker amp. connector B121 and suspec ..

B2190, P1610 nats antenna amp
Description Performs ID verification through BCM and keyfob when push-button ignition switch is pressed. Prohibits the release of steering lock or start of engine when an unregistered ID of keyfob is used. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMA ..

Th3InfamousI

Ultima Oil Pump Diagram